Body
Using a 4.0 mm crochet hook and Color A yarn…
Round 1: Magic Ring with a base of 7 sc (7 sts)
Round 2: Sc inc in each st around (14 sts)
Round 3: [Sc, sc inc] x 7 times (21 sts)
Round 4: [2 sc, sc inc] x 7 times (28 sts)
Round 5: Sc in each st around (28 sts)
Change to Colour B yarn…
Round 6: Slst in each st around (28 sts)
Round 7: Sc in the back loop only of each st around (28 sts)
Round 8-10: Sc in each st around (28 sts)
Round 11: [2 sc, sc dec] x 7 times (21 sts)
Round 12: [Sc, sc dec] x 7 times (14 sts)
Fasten off and leave a tail to sew onto the hood.

Arms (Make 2)
Using a 4.0 mm crochet hook and Color A yarn…
Round 1: Magic Ring with a base of 6 sc (6 sts)
Round 2: [Sc, sc inc] x 3 times (9 sts)
Round 3: Sc in each st around (9 sts)
Change to Colour B yarn…
Round 4: Slst in each st around (9 sts)
Round 5: Sc in the back loop only of each st around (9 sts)
Round 6: [Sc, sc dec] x 3 times (6 sts)
Round 7-8: Sc in each st around (6 sts)
Fasten off and leave a tail to sew onto the body.

Legs (Make 2)
Using a 4.0 mm crochet hook and Color A yarn…
Round 1: Magic Ring with a base of 6 sc (6sts)
Round 2: Sc inc in each st around (12 sts)
Round 3: [Sc, sc inc] x 6 times (18 sts)
Round 4-6: Sc in each st around (18 sts)
Round 7: [Sc, sc dec] x 6 times (12 sts)
Stuff firmly as you continue to decrease.
Round 8: Sc dec in each st around (6 sts)
Round 9: Sc in each st around (6 sts)
Fasten off, leaving a tail to sew onto the body.

Tail
Using a 4.0 mm crochet hook and Color A yarn…
Round 1: Magic Ring with a base of 6 sc (6 sts)
Round 2: Sc inc in each st around (12 sts)
Round 3: Sc in each st around (12 sts)
Round 4: Sc dec in each st around (6 sts)
Fasten off and leave a tail to sew to the body.
After that, you basically have all your pieces ready to go.

FYI, this photo is missing the tail piece

ASSEMBLY
On the hood, you have two slits, these are for your bunny’s ears. To line them up correctly, the ears should sit right on top of the head. I attached it right after the 􀁺rst round (photo 2)

Then, position your bunny’s head by placing it inside the hood with the ears through the slits. Make sure that your bunny’s eyes are facing outside.

Using the long strand that you left on the head, sew bottom of the head to the bottom of the hood (photo 7).

On the bottom of the hood where you sewed the head, you’ll see yarn in Colour A but don’t worry as this will be hidden once the body is attached.

Next, attach your tail to the body, as well as the arms and legs. And then attach the head along with the hood to the body.

If the head and body are attached properly, you should no longer be able to see Colour A yarn on the bottom of the hood. After that, you sew on the details of the bunny’s face and then you’re done!

And there you have it your very own Bunny in the Hood! Look at that, a family reunion!